点击图片查看原图
T8-日光灯-9W 9W ￠26*30*600 AC110-245V 75LM-80LM/W 透明/乳白/光扩罩 88S-3014
T8-日光灯-12W 12W ￠26*30*900 AC110-245V
75LM-80LM/W 透明/乳白/光扩罩 132S-3014
T8-日光灯-12W 12W ￠26*30*1200 AC110-245V 75LM-80LM/W 透明/乳白/光扩罩 126S-3014
T8-日光灯-15W 15W ￠26*30*1200 AC110-245V
75LM-80LM/W 透明/乳白/光扩罩 154S-3014
T8-日光灯-18W 18W ￠26*30*1200 AC110-245V
75LM-80LM/W 透明/乳白/光扩罩 184S-3014
T8-日光灯-8W 8W ￠26*30*600 AC110-245V
75LM-80LM/W 透明/乳白/光扩罩 120S-3528
T8-日光灯-10W 10W ￠26*30*600 AC110-245V
75LM-80LM/W 透明/乳白/光扩罩 144S-3528
T8-日光灯-15W 15W ￠26*30*1200 AC110-245V
75LM-80LM/W 透明/乳白/光扩罩 240S-3528
T8-日光灯-18W 18W ￠26*30*1200 AC110-245V
75LM-80LM/W 透明/乳白/光扩罩 288S-3528
LED Tube comparison with the traditional fluorescent tube:
Emitting principle: LED lamp: support DC power supply to the light-emitting
element, light emitting, no flicker; mercury-free, will not pollute the indoor
and environmental.
The traditional fluorescent rely on electron bombardment mercury vapor to
generate ultraviolet rays irradiated phosphor and light, electron bombardment
mercury vapor, ultraviolet radiation emitting phosphor lamp process are random,
discontinuous, so very serious, strobe. A 1.2 m T8 fluorescent weld
grams of mercury, the mercury will escape, pollution of the environment with
the increased use of time.
LED light energy than traditional fluorescent lamps, an LED fluorescent nodes
lamp 18W nominal power, 20% -30% higher than 40W fluorescent fluorescent light,
the energy-saving effect alarming.
LED light long life: an LED fluorescent, if the choice of high-quality
electrolytic capacitors accessories as a constant current source, a life span
of over 50,000 hours, 50,000 hours lifetime can be higher than if the choice of
non-electrolytic capacitor device as a constant current source accessories. The
light is small: the average qualified LED fluorescent thousand-time decline of
less than 3% of the traditional fluorescent lamp small-time decline of 8% or
more.
LED fluorescent ultraviolet. Ultraviolet small amount of radiation is
beneficial to the people. Irradiation for a long time can damage cells: such as
darkening of the skin, severe induced cancer. Traditional fluorescent lamp
needs ultraviolet light phosphors to light-emitting light in the ultraviolet
content, long-term exposure is not conducive to health.
LED fluorescent serviceable. General failure in a constant current source, and
can work just replaced the constant current source. The lamp beads failures are
generally few lights beads, lamp beads making process a small amount of dead
beads chip technology, as long as the replacement of old. The traditional
fluorescent fluorescent lamp bad, the latter can not be repaired, and the waste
is difficult to deal with, and can not be discarded, but also can not be
reused.
The LED fluorescent facilitates secondary control. LED for DC power supply, the
start-up time is short, almost directly start. So, with infrared control head
voice head, radar lights with the realization of intelligent control.
Traditional fluorescent lamps because of a slow start, is not conducive to the
realization of intelligent control.
LED fluorescent tube office lighting advantage
1, environmentally friendly lamps, protect the earth; contains large amounts of
mercury vapor in the traditional fluorescent broken mercury vapor will
evaporate into the atmosphere. LED fluorescent lamp does not use mercury and
LED products do not contain lead, play a protective effect on the environment.
Efficient light-emitting, reduce losses; traditional luminaire direction of 360
degrees, LED lighting is directional luminous, will not cause the loss of
light.
3, quiet and comfortable, no noise: LED lamps do not produce noise, using
precision electronic instruments occasions Choice. Suitable for a library,
offices and the like occasions.
4, soft light, protect the eyes: the traditional fluorescent lamp is AC, so
100-120 times per second strobe. LED lamps directly convert the AC to DC, will
not produce flicker, protect your eyes.
5, no UV, no mosquitoes: LED lamps do not produce ultraviolet light, and
therefore will not like traditional lamps, there are a lot of mosquitoes around
the light source side. The Indoor become more clean sanitation and clean.
Voltage adjustable 80V-265V; the conventional fluorescent lit by high voltage
rectifier release, you can not light up when the voltage decreases. LED lamps
can be lit in a certain range of voltage can also adjust the brightness of the
light.
7, energy savings and longer life
LED fluorescent lamp power consumption is half of the traditional fluorescent
lamp, life expectancy is 10 times the traditional fluorescent, long-term use without
the need to replace, reduce labor costs. More suitable for occasions that are
difficult to replace.
8, robust, secure, long-term use; LED lamp body is epoxy instead of the
traditional glass, more robust, secure, LED also will not easily be damaged even
hit the floor, you can safely use.
LED Tube Installation Notes
1, the installation:
LED comes with a constant current source, does not require rectifiers, starter.
Generally over T8 lamp because the lamp space enough, the constant current
source can be installed on the inside of the lamp. So, when installed, you can
remove the original bracket in the rectifier, starter without lamp installed
directly up on it.
T5, T5LED fluorescent lamp because the lamp is small, does not fit the constant
current source, constant current source can only be mounted in the holder, so
manufacturers are doing T4 \ T5 will be configured in the bracket, bracket
equipped with a constant current source, and directional lamp installed.
Opposite direction, the lamp is not lit. We are considering adding some
conversion circuit, so that even if the lamp is installed anti circumstances,
the lamp can work properly.
2, voltage: Blue King photoelectric production of fluorescent lamps have a very
wide voltage adaptability, AC 85V - AC 245V, can be normal work. But the
long-term voltage is too high or too low, it will affect the power factor of
the constant current source, That will cause a slight impact of energy-saving
effect. At the same time, it will also affect the life of the constant current
source. Therefore, the general selection of appropriate voltage fluorescent
tubes. Such as: mains 110V places, you should use a specially designed 110 mains
fluorescent tubes.
3, cooling: Blue King photoelectric production of fluorescent lamps with
aluminum enclosure's heat dissipating heat is not a problem under normal
circumstances. However, where heavy dust, should regularly dust to prevent dust
covering the radiator, the impact of heat.
4, Waterproof: LED fluorescent lamp because the lamp is composed of two parts
from top to bottom: the upper part of the aluminum radiator for the next part
of the soft mask, there are gaps in the joints, so to prevent soot, water vapor
from entering. If you use heavier in the flue gas, water vapor, and suggested
adding a protective cover. Usually the protective cover on it.
5, vibration: LED lamp has a strong anti-vibration ability. As long as it is
not a violent shock, usually does not cause damage. Some impact but might be a
soft board. Traditional fluorescent glass, which is close to the vacuum,
vibration could cause an explosion, with particular attention to vibration.
LED Tube purchasing skills
Choose the right color temperature. LED fluorescent installation location, you
can buy the high color temperature, such as: 6500K - 7000K., Light color seems
a bit bluish. As LED light efficiency is relatively high, despite a bit harsh,
but because of the installation location, direct exposure to the eye a very
small chance. Kind: If the installation location, the eyes direct exposure
opportunities, you should choose the color temperature low, close to daylight
color temperature of 5500K - 6000K. As the softer light eyes feel comfortable.
Optional LED fluorescent tubes also need to consider the appropriate power. LED
Fluorescent same energy consumption, and its luminous flux emitted difference
great selection of high-quality, large luminous flux LED fluorescent
alternative to the traditional fluorescent lamp, due consideration to install
some less. Do not substitute with the traditional fluorescent 1:1. In this way,
more energy-efficient.
Choose the right appearance: the general LED fluorescent in the concept of
users are still stuck in the traditional fluorescent stage. So, no matter what
the situation requires light with traditional fluorescent. Plus soft board
manufacturers in the LED fluorescent tube light looks like. In fact, the soft
plate light energy loss. In general between 15-30%. If the installation
location is not easy, eyes often irradiated, can be considered with a
transparent cover, as can choose to power small LED fluorescent light, will be
more energy efficient.
Choose the right type of fluorescent tubes. Fluorescent lights use low power
SMD lamp beads, overall calorific much. But if there is a better heat light
fades further reduce the increase in life expectancy. The LED fluorescent form,
the radiator area much larger heat Hao. If possible, try to use T8 \ T10 tubes.
Of course, T10 tube shape, and its cost is also high, based on experience, T8
tube most appropriate. T4 \ T5 smaller points. Especially T4 tube, power can
not choose large.
